tc4 tcxo series surface mount or full size metal thru-hole temperature compensated xtal oscillator hcmos, clipped sine wave or sine wave compatible rohs compliance: not recommended for use in high temperature lead free assembly process. use tca4, tcd4 series standard specifications overall frequency 1.0 to 10 ppm over operating temperature range available operating temperature range 0 to +50 c to -40 to +85 c available supply voltage (vcc) 5.0 volts and 3.3 volts available output load (see test circuit 1) 10 ttl loads or 15pf part numbering guide tcxo package, max height frequency stability (fs) frequency in mhz 3tc4 6 h 100 a - 10.0m - xxx (internal code or blank) (425) 776 - 1880, fax: (425) 776- 2760, ple- sales@pletronics.com, www.pletronics.com 26 nov 2005 pl tronics, inc. mechanical: not to scale inches (mm) 6=thru-hole, 5.0mm 7=surface mount, 5.5mm 8=surface mount, 4.0mm 9=thru-hole, 8.5mm hcmos clipped sine wave operating temperature range {tightest fs available} a: 0 to +50 c {1.0 ppm } b: 0 to +70 c {1.5 ppm } c: -10 to +70 c { 2.0 ppm } d: -20 to +75 c { 2.0 ppm } e: -30 to +75 c { 2.5 ppm } f: -40 to +85 c { 5.0 ppm } 010: 1.0 ppm 015: 1.5 ppm 020: 2.0 ppm 025: 2.5 ppm model / supply voltage tc4= 5.0 volts 5% 3tc4= 3.3 volts 5% stability vs. temp vs. vcc / load aging 0.5 ppm maximum over vcc 5% / 0.3 ppm maximum over load 5% 3 ppm first year, 1 ppm per year thereafter at 25 c 5% frequency adj by trimmer 3 ppm minimum output logic sine wave logic ?1? 90% of vcc min logic ?0? 10% of vcc max 1 volt p-p minimum output voltage levels supply current (icc) 20 to 40 ma max 2 to 5 ma max 10 k // 10 pf 030: 3.0 ppm 050: 5.0 ppm 100: 10.0 ppm logic c: clipped sine wave h: hcmos s: sine wave package 6 package 7 package 9 package 8 consult factory for available frequencies and specs. not all options available for all frequencies. a special part number may b e assigned. frequency stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load consult factory packaging tube or on pads, smd: bulk due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal co de. on test circuit for clipped sine wave only: add a 20 k resistor from output to ground timmer hole locations may vary pl tronics , inc. 19013 36th ave. w, suite h lynnwood, wa 98036 usa manufacturer of high quality frequency control products . portions of the part number that appear after the frequency may not be marked on part (c of c provided) .748 (19.0) max .492 (12.5) max .600 (15.24) .300 (7.62) 8 14 7 vcc out gnd 10.00 mhz ? 60.00 mhz .740 (18.8) max .461 (11.7) max .600 (15.24) .300 (7.62) 8 14 7 1 n.c. vcc out gnd .157 (4.0) .457 (11.6) .386 (9.8) vcc gnd out gnd gnd (2.54) typ .055 (1.4) .110 (2.8) n.c. 3 4 12 .799 (20.3) .335 (8.5) max vcc out gnd gnd .457 (11.6) .300 (7.62) max .360 (9.14) .600 (15.24) .600 (15.24) .799 (20.3) .217 (5.5) max .197 (5.0) max .193 (4.9) min ta b .04 x .10 (1.0 x 2.5) .66 (16.76) .12 (3.0) .17 .04 x .20 (1.0 x 5.08) .100 (4.3) .858 (21.8) max .157 (4.0) min
|
